sam@knockspy – KnockSpy Blog http://localhost:8080 Fri, 18 Mar 2022 17:20:56 +0000 en-US hourly 1 https://wordpress.org/?v=6.9.4 ConsultSpy Digital Dashboard http://localhost:8080/archives/117 Fri, 18 Mar 2022 17:20:56 +0000 http://knockspy.com/blog/?p=117 The next iteration of ConsultSpy is progressing, now with digital dashboard and gauge display.

  • Digital Dashboard with gauges, customizable layouts and min/max warnings
  • Presets for vehicle specific groups of data monitors, such as Knock, TPS, Acceleration Enrichment
  • Touchscreen UI with left/right swiping to quickly change layouts
  • Reskinned front-end
  • Google Play Billing integration. Licensing is now handled entirely through the Google Play store, without the need to purchase through PayPal. Four feature levels are available, Free, Basic, Tuner and Pro Tuner.
Connect sequence, using the touchscreen to show/hide gauges and set a maximum warning for RPM.
Touchscreen swipe to quickly change layouts
Adding a live data monitor for a Wideband O2 UEGO sensor, connected to a 0-5v aux input on a Nistune ECU.

]]> New ConsultSpy Build Available http://localhost:8080/archives/115 Thu, 12 Nov 2020 03:17:46 +0000 http://knockspy.com/blog/?p=115 A  new version of ConsultSpy is now available for download through the website and Google Play.

New features:

  • Status indicator lights on the main screen
  • Support for PLMS USB Consult adapters
  • Data monitors are now grouped
  • Metric/standard units
  • Nistune tuning options for VTC, Injectors, TPS

New Data Monitors:

  • Acceleration Enrichment fuel
  • Wall-wetting fuel
  • Fuel Map A/F Target
  • TPS Delta
  • Ignition Dwell
  • Injector Latency
  • TPS idle self-learn
  • Auxiliary 0-5v analog input (for Ethanol Content, Wideband O2, MAP, EGT, etc)
]]> ConsultSpy Development Update http://localhost:8080/archives/106 Wed, 07 Oct 2020 18:43:50 +0000 http://knockspy.com/blog/?p=106 The next build of ConsultSpy has some significant changes behind the scenes including a new connect sequence and status indicator lights on the main screen.

The main screen has indicators lights for the following:

  • ECU connection status
  • ECU ROM sync status
  • Data Stream On
  • Active Tests On
  • Data Log Recording
  • Connection Type (Bluetooth or USB)
  • Receive data (RX)
  • Transmit data (TX)

]]> TPS idle soft and hard switch operation http://localhost:8080/archives/96 Sat, 18 Apr 2020 17:50:24 +0000 http://knockspy.com/blog/?p=96

The Z32 has a redundant idle detection system that utilizes both a soft-switch and hard-switch as described in the factory service manual on page EF&EC-15.  The ECU relies primarily on the soft-switch and falls back to using the hard-switch only when it detects a fault in TPS operation.

The soft-switch is calculated in software by the ECU and determines idle condition based on changes in TPS voltage.  It has a self-learn function that remembers the lowest TPS voltage and compares the current TPS voltage to this every 10 milliseconds.  If the difference between the current TPS voltage and self-learn voltage is less than a (small) threshold value, the idle condition is turned ON.  Conversely, when the voltage difference goes above this threshold, the idle condition is turned OFF.  If the TPS voltage goes lower than the self-learn voltage, the ECU re-adjusts the idle self-learn voltage to this new low value.  The ECU falls back to using the idle hard-switch only when the TPS sensor voltage goes out of range.   The allowable range for TPS operation is between 0.04v and 4.82v.  If the TPS voltage goes below or above this range, a TPS error state is triggered.  If this error occurs repeatedly over time with the vehicle at speed greater than 4km/h, an ECU fault code 43 will eventually be triggered.

ConsultSpy can be used to monitor TPS idle operation using the Throttle Position, TPS Voltage, TPS Min Learn, and Error State #1 data monitors.

Idle hard-switch fall-back operation:

Soft-switch self learn readjusting to a lower TPS position as the minimum TPS voltage drops

]]> Wideband Oxygen Sensor Support http://localhost:8080/archives/90 Tue, 26 Nov 2019 21:09:23 +0000 http://knockspy.com/blog/?p=90 ConsultSpy can now monitor and log Wideband Oxygen Sensors connected directly to the ECU, with support for linear 0-5v and non-linear UEGO wideband controllers. This feature will be available in Build 1.015.

]]> New Build Available http://localhost:8080/archives/82 Wed, 30 Oct 2019 23:11:26 +0000 http://knockspy.com/blog/?p=82 Build 1.014 has been released to the internal test network.

]]> Self Learn Fuel-Trim Maps http://localhost:8080/archives/62 Sun, 27 Oct 2019 20:25:45 +0000 http://knockspy.com/blog/?p=62 The ECU adjusts fuel-trims based on Oxygen sensor feedback and stores these adjustments in the self-learn fuel-trim maps. ConsultSpy can download and view these fuel maps, providing valuable insight into the health of the fuel system and oxygen sensors.

]]> Consult Active Tests http://localhost:8080/archives/59 Sun, 27 Oct 2019 20:19:34 +0000 http://knockspy.com/blog/?p=59 ConsultSpy supports standard Nissan Consult Active Tests, and can enable up to five tests simultaneously.

]]> USB Consult Adapter Support http://localhost:8080/archives/57 Sun, 27 Oct 2019 20:13:30 +0000 http://knockspy.com/blog/?p=57 ConsultSpy now supports wired USB Consult adapters. Devices can be selected in Settings.

]]> ConsultSpy Dual-Bank Cylinder Cut Demo http://localhost:8080/archives/36 Mon, 14 Oct 2019 00:40:18 +0000 http://knockspy.com/blog2/?p=36 This video shows a comparison between single and dual-bank cylinder cut used by the launch control rev-limiter. From the factory, the rev-limiter in Z32 and R32 ECUs cuts fuel to the right-side cylinder bank before any left-side cylinders are cut. This results in reduced Exhaust Gas Temperature (EGT) in the right-bank and lowers turbo boost. By changing to a dual-bank cylinder cut, cylinders are dropped equally between banks and EGT is increased for improved turbo response.

]]>